Walrus Audio Eras Five-State Distortion - Black

ERAS
Five-State Distortion

Eras is a no apologies, high-gain distortion that’s ready to chug, shred, and palm mute with tight response and multiple clipping options. Use the Blend knob at max for a full distortion onslaught or roll back the Blend knob to creatively stack and mix other dirt pedals placed in front of Eras. Great for bassists that want to blend in their dry signal as well. Anywhere you set it, the Eras is ready to deliver a diverse world of speaker ripping sounds.

Think of each position as a different “flavor” of the pedal. Blend in dry signal or other pedals in combination with the gain states for a near-infinite amount of distortion sounds.

Controls:

VOL – The Volume knob sets the overall output volume of the pedal. The Eras has quite a bit of volume on tap, so the Volume knob will be helpful to find the sweet spot for interacting with the rest of your rig.
BLEND – The Blend knob allows you to blend between your fully clean and fully distorted signal. With this control at minimum, the output is your original, fully clean input with no distortion. As you turn the knob to the right, more distortion is added. At maximum, the output is the fully distorted signal with no clean blended in. Blending the clean and distorted signals allows you to increase note clarity as the clean and distorted channels run parallel to each other inside of the Eras. If you run a boost, overdrive, or other distortion before the Eras you can create a unique mixture between the two using the Blend control. Any gain added before the Eras input will affect both the internal clean and dirty channels. The Blend knob is great for bassists as well.
GAIN – The Gain knob sets the amount of gain applied to your guitar signal passing through the overdrive circuit.
BASS – The Bass control allows you to cut or boost low frequencies after the distortion circuit. This can help tighten up the low-end or increase low-frequency emphasis. The low-frequency response of the Eras is interactive with the gain control, so at higher gain, there is naturally more bass, while at lower gain, there is less bass. The Bass knob helps to balance out the wide range of gain that the Eras offers. Starting at noon, turn down to remove bass and turn up to add bass.
TREB – The Treble control allows you to increase treble to punch through a mix at high gain, or roll off to smooth out low gain signals. Like the bass control, you may find that at higher gain, you will want to add more treble, and at lower gain, you may want to roll the treble back. Starting at noon, turn down to cut out highs and turn up to allow more highs.
MODE SWITCH – The Mode switch is a five-position rotary switch. Each position offers a different combination of internal gain and clipping styles employed by the pedal. You can think of each position as a different “flavor” of the pedal.

MODE SWITCH:

I.   Tight mode with a slight mid-cut, LED hard- clipping, and internal volume compensation. Fastest response, great for palm muting.
II.  Tight mode with a slight mid-cut and silicon hard clipping. Smooth with added compression.
III. Dual clipping mode with a slight mid-cut and both silicon and LED hard-clipping. Rich & full with added sustain.
IV.  Rhythm mode with a deeper mid-cut, LED hard- clipping, and internal volume compensation. Scooped mids, tight response.
V.   Rhythm mode with a deeper mid-cut and silicon hard-clipping. Rhythmic, warm and full.

Specifications:

• True Bypass
  
• The Eras comes in a “transparent red” enclosure color with yellow, cream and black ink. Artwork features a stoic four horned, winged bull illustrated by Adam Forster.
  
• 9V DC, center negative,  100mA min – 2.62 x 4.77 x 2.25 inches including knobs.
  
• The use of an isolated power supply is recommended for powering all Walrus Audio Pedals.
  
• Daisy chain power supplies are not recommended.
  
• Power supply not included.